View TL062-D_2941968.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

low power jfet input operational amplifiers these jfet input operational amplifiers are designed for low power applications. they feature high input impedance, low input bias current and low input offset current. advanced design techniques allow for higher slew rates, gain bandwidth products and output swing. the commercial and vehicular devices are available in plastic dual inline and soic packages. ? low supply current: 200 m a/amplifier ? low input bias current: 5.0 pa ? high gain bandwidth: 2.0 mhz ? high slew rate: 6.0 v/ m s ? high input impedance: 10 12 w ? large output voltage swing: 14 v ? output short circuit protection representative schematic diagram (each amplifier) + q3 q2 q1 - + r2 r5 j1 j2 r1 q4 c1 q5 d2 r3 q7 r4 v cc output d1 c2 q6 v ee inputs ordering information op amp function device operating temperature range package tl062cd, acd tl062cp, acp t a = 0 to +70 c so8 plastic dip dual tl062vd tl062vp t a = 40 to +85 c so8 plastic dip tl064cd, acd tl064cn, acn t a = 0 to +70 c so14 plastic dip quad tl064vd tl064vn t a = 40 to +85 c so14 plastic dip on semiconductor ? semiconductor components industries, llc, 2002 march, 2002 rev. 6 1 publication order number: tl062/d tl062 tl064 semiconductor technical data low power jfet input operational amplifiers d suffix plastic package case 751 (so8) p suffix plastic package case 626 8 1 1 8 dual pin connections (top view) v ee inputs 1 output 1 inputs 2 output 2 v cc - + 1 2 3 4 8 7 6 5 - + d suffix plastic package case 751a (so14) n suffix plastic package case 646 14 1 14 1 quad pin connections (top view) 4 23 1 inputs 1 output 1 v cc inputs 2 output 2 output 4 inputs 4 v ee inputs 3 output 3 1 2 3 4 5 6 78 9 10 11 12 13 14 + + + - + -
tl062 tl064 http://onsemi.com 2 maximum ratings rating symbol value unit supply voltage (from v cc to v ee ) v s +36 v input differential voltage range (note 1) v idr 30 v input voltage range (notes 1 and 2) v ir 15 v output short circuit duration (note 3) t sc indefinite sec operating junction temperature t j +150 c storage temperature range t stg 60 to +150 c notes: 1. differential voltages are at the noninverting input terminal with respect to the inverting input terminal. 2. the magnitude of the input voltage must never exceed the magnitude of the supply or 15 v, whichever is less. 3. power dissipation must be considered to ensure maximum junction temperature (t j ) is not exceeded. (see figure 1.) electrical characteristics (v cc = +15 v, v ee = 15 v, t a = 0 to +70 c, unless otherwise noted.) tl062ac tl064ac tl062c tl064c characteristics symbol min typ max min typ max unit input offset voltage (r s = 50 w , v o = 0v) t a = 25 c t a = 0 to +70 c v io e e 3.0 e 6.0 7.5 e e 3.0 e 15 20 mv average temperature coefficient for offset voltage (r s = 50 w , v o = 0 v) d v io / d t e 10 e e 10 e m v/ c input offset current (v cm = 0 v, v o = 0 v) t a = 25 c t a = 0 to +70 c i io e e 0.5 e 100 2.0 e e 0.5 e 200 2.0 pa na input bias current (v cm = 0 v, v o = 0 v) t a = 25 c t a = 0 to +70 c i ib e e 3.0 e 200 2.0 e e 3.0 e 200 10 pa na input common mode voltage range t a = 25 c v icr e 11.5 +14.5 12.0 +11.5 e e 11 +14.5 12.0 +11 e v large signal voltage gain (r l = 10 k w , v o = 10 v) t a = 25 c t a = 0 to +70 c a vol 4.0 4.0 58 e e e 3.0 3.0 58 e e e v/mv output voltage swing (r l = 10 k w , v id = 1.0 v) t a = 25 c v o + v o +10 e +14 14 e 10 +10 e +14 14 e 10 v t a = 0 to +70 c v o + v o +10 e e e e 10 +10 e e e e 10 common mode rejection (r s = 50 w , v cm = v icr min, v o = 0 v, t a = 25 c) cmr 80 84 e 70 84 e db power supply rejection (r s = 50 w , v cm = 0 v, v o = 0, t a = 25 c) psr 80 86 e 70 86 e db power supply current (each amplifier) (no load, v o = 0 v, t a = 25 c) i d e 200 250 e 200 250 m a total power dissipation (each amplifier) (no load, v o = 0 v, t a = 25 c) p d e 6.0 7.5 e 6.0 7.5 mw
tl062 tl064 http://onsemi.com 3 dc electrical characteristics (v cc = +15 v, v ee = 15 v, t a = t low to t high [note 4], unless otherwise noted.) tl062v tl064v characteristics symbol min typ max min typ max unit input offset voltage (r s = 50 w , v o = 0v) t a = 25 c t a = t low to t high v io e e 3.0 e 6.0 9.0 e e 3.0 e 9.0 15 mv average temperature coefficient for offset voltage (r s = 50 w , v o = 0 v) d v io / d t e 10 e e 10 e m v/ c input offset current (v cm = 0 v, v o = 0 v) t a = 25 c t a = t low to t high i io e e 5.0 e 100 20 e e 5.0 e 100 20 pa na input bias current (v cm = 0 v, v o = 0 v) t a = 25 c t a = t low to t high i ib e e 30 e 200 50 e e 30 e 200 50 pa na input common mode voltage range (t a = 25 c) v icr e 11.5 +14.5 12.0 +11.5 e e 11.5 +14.5 12.0 +11.5 e v large signal voltage gain (r l = 10 k w , v o = 10 v) t a = 25 c t a = t low to t high a vol 4.0 4.0 58 e e e 4.0 4.0 58 e e e v/mv output voltage swing (r l = 10 k w , v id = 1.0 v) t a = 25 c t a = t low to t high v o + v o v o + v o +10 e +10 e +14 14 e e e 10 e 10 +10 e +10 e +14 14 e e e 10 e 10 v common mode rejection (r s = 50 w , v cm = v icr min, v o = 0, t a = 25 c) cmr 80 84 e 80 84 e db power supply rejection (r s = 50 w , v cm = 0 v, v o = 0, t a = 25 c) psr 80 86 e 80 86 e db power supply current (each amplifier) (no load, v o = 0 v, t a = 25 c) i d e 200 250 e 200 250 m a total power dissipation (each amplifier) (no load, v o = 0 v, t a = 25 c) p d e 6.0 7.5 e 6.0 7.5 mw note: 4. t low = 40 ct high = +85 c for tl062,4v ac electrical characteristics (v cc = +15 v, v ee = 15 v, t a = +25 c, unless otherwise noted.) characteristics symbol min typ max unit slew rate (v in = 10 v to +10 v, r l = 10 k w , c l = 100 pf, a v = +1.0) sr 2.0 6.0 e v/ m s rise time (v in = 20 mv, r l = 10 k w , c l = 100 pf, a v = +1.0) t r e 0.1 e m s overshoot (v in = 20 mv, r l = 10 k w , c l = 100 pf, a v = +1.0) os e 10 e % settling time (v cc = +15 v, v ee = 15 v, a v = 1.0, to within 10 mv r l = 10 k w , v o = 0 v to +10 v step) to within 1.0 mv t s e e 1.6 2.2 e e m s gain bandwidth product (f = 200 khz) gbw e 2.0 e mhz equivalent input noise (r s = 100 w , f = 1.0 khz) e n e 47 e nv/ hz input resistance r i e 10 12 e w channel separation (f = 10 khz) cs e 120 e db
tl062 tl064 http://onsemi.com 4 v cc = +15 v, v ee = -15 v r l = 10 k w t a = 25 c v cc = +12 v, v ee = -12 v v cc = +5.0 v, v ee = -5.0 v v cc = +2.5 v, v ee = -2.5 v v o , output voltage swing (v pp ) v o , output voltage swing (v pp ) t a , ambient temperature ( c) a vol , large signal voltage gain (v/mv) -75 -50 -25 0 25 75 50 100 125 v cc = +15 v v ee = -15 v r l = 10 k w figure 1. maximum power dissipation versus temperature for package variations figure 2. output voltage swing versus supply voltage figure 3. output voltage swing versus temperature figure 4. output voltage swing versus load resistance figure 5. output voltage swing versus frequency figure 6. large signal voltage gain versus temperature t a , ambient temperature ( c) d p, maximum power dissipation (mw) -55 -40 -20 0 20 40 60 80 100 120 140 160 so-14 so-8 v cc , |v ee |, supply voltage (v) 0 2.0 4.0 6.0 8.0 10 12 14 16 r l = 10 k w t a = 25 c t a , ambient temperature ( c) -75 -50 -25 0 25 50 75 100 125 v cc = +15 v v ee = -15 v r l = 10 k w r l , load resistance (k w ) 0.1 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 v cc = +15 v v ee = -15 v t a = 25 c f, frequency (hz) 100 1.0 k 10 k 100 k 1.0 m 10 m 10 20 30 40 50 70 100 0 400 800 1200 1600 2000 2400 0 5.0 10 15 20 25 30 35 40 0 5.0 10 15 20 25 30 35 40 0 6.0 12 18 24 30 0 5.0 10 15 20 25 30 35 v o , output voltage swing (v pp ) v o , output voltage swing (v pp )
tl062 tl064 http://onsemi.com 5 v cc = +15 v v ee = -15 v v o = 0 v r l = w phase gain v cc = +15 v v ee = -15 v v o = 0 v r l = 10 k w c l = 0 pf t a = 25 c figure 7. open loop voltage gain and phase versus frequency figure 8. supply current per amplifier versus supply voltage figure 9. supply current per amplifier versus temperature figure 10. total power dissipation versus temperature figure 11. common mode rejection versus temperature figure 12. common mode rejection versus frequency f, frequency (hz) vol a, open loop voltage gain (db) 1.0 10 100 1.0 k 10 k 1.0 m 10 m 100 m 100 k , excess phase (degrees) f f, frequency (hz) cmr, common mode rejection (db) 100 1 k 10 k 100 k 1 m v cc , |v ee |, supply voltage (v) 0 2.0 4.0 6.0 8.0 10 12 14 16 18 20 t a , ambient temperature ( c) -75 -50 -25 0 25 50 75 100 125 i cc , supply current ( m /a) p d , total power dissipation (mw) t a , ambient temperature ( c) 125 100 75 50 25 0 -25 -50 -75 tl064 tl062 t a , ambient temperature ( c) cmr, common mode rejection (db) 125 100 75 50 25 0 -25 -50 -75 i cc , supply current ( m a) 100 80 60 40 20 0 140 120 100 80 60 40 20 0 0 50 100 150 200 250 0 50 100 150 200 250 0 5.0 10 15 20 25 80 81 82 83 84 85 86 87 88 0 45 90 135 180 v cc = +15 v v ee = -15 v d v cm = 1.5 v t a = 25 c t a = 25 c v o = 0 v r l = w v cc = +15 v v ee = -15 v v o = 0 v r l = w v cc = +15 v v ee = -15 v v o = 0 v r l = 10 k w cmr = 20 log a dm - + d v cm d v o x a dm d v cm d v o
tl062 tl064 http://onsemi.com 6 v cc = +15 v v ee = -15 v r s = 100 w t a = 25 c +psr = 20log d v o /a dm d v cc -psr = 20log d v o /a dm d v ee +psr ( d v cc = 1.5 v) -psr ( d v ee = 1.5 v) v cc = +15 v v ee = -15 v t a = 25 c v cc v ee a dm - + d v o figure 13. power supply rejection versus frequency figure 14. normalized gain bandwidth product, slew rate and phase margin versus temperature figure 15. input bias current versus temperature figure 16. input noise voltage versus frequency figure 17. small signal response figure 18. large signal response f, frequency (hz) psr, power supply rejection (db) 100 1.0 k 10 k 100 k 1.0 m t a , ambient temperature ( c) normalized gain bandwidth product and slew rate -75 -50 -25 0 25 50 75 100 125 m f , normalized phase margin phase margin slew rate t a , ambient temperature ( c) i ib , input bias current (pa) -55 -25 0 25 50 75 100 125 v cc = +15 v v ee = -15 v v cm = 0 v f, frequency (hz) e n , input noise voltage ( 10 100 1.0 k 10 k 100 k ) nv/ hz t, time (0.5 m s/div) v o , output voltage (10 mv/div) v cc = +15 v v ee = -15 v r l = 10 k w c l = 0 pf a v = +1.0 t, time (2.0 m s/div) v o , output voltage (5.0 v/div) gbw v cc = +15 v v ee = -15 v r l = 10 k w c l = 0 pf a v = +1.0 140 120 100 80 60 40 20 0 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 0.001 0.01 0.1 1.0 10 100 1000 0 10 20 30 40 50 60 70 1.08 1.06 1.04 1.02 1.0 0.98 0.96 0.94 0.92 v cc = +15 v v ee = -15 v r l = 10 k w c l = 0 pf
tl062 tl064 http://onsemi.com 7 c3 2 1 2 p r1 c1 figure 19. ac amplifier figure 20. highq notch filter figure 21. instrumentation amplifier figure 22. 0.5 hz squarewave oscillator figure 23. audio distribution amplifier + 1/2 tl062 5 1 250 k w 10 k w 50 w v cc output 1.0 m w 0.1 m f inputs - 10 k w 10 k w 0.1 m f v cc v ee output r2 r1 c3 r3 c2 c1 input r1 = r2 = 2r3 = 1.5 m w c1 = c2 = = 110 pf f o = = 1.0 khz - + + - tl064 input a 10 k w 0.1% v cc output v cc v cc v cc v ee v ee v ee v ee - - - + + + tl064 tl064 tl064 input b 100 k w 10 k w 0.1% 10 k w 0.1% 10 k w 0.1% 100 k w 100 w 1.0 m w 1 c f = 3.3 m f r f = 100 k w +15 v + - -15 v 9.1 k w f = 1.0 k w 3.3 k w 3.3 k w + - tl064 v cc 1.0 m w 100 k w v cc 100 m f v cc v cc v cc 1.0 m f input output a output b output c - - - + + + tl064 tl064 tl064 100 k w 100 k w 100 k w 100 k w 1/2 tl062 1/2 tl062 2 p r f c f
tl062 tl064 http://onsemi.com 8 p suffix plastic package case 62605 issue k d suffix plastic package case 75105 (so8) issue r outline dimensions 14 5 8 f note 2 a b t seating plane h j g d k n c l m m a m 0.13 (0.005) b m t notes: 1. dimension l to center of lead when formed parallel. 2. package contour optional (round or square corners). 3. dimensioning and tolerancing per ansi y14.5m, 1982. dim min max min max inches millimeters a 9.40 10.16 0.370 0.400 b 6.10 6.60 0.240 0.260 c 3.94 4.45 0.155 0.175 d 0.38 0.51 0.015 0.020 f 1.02 1.78 0.040 0.070 g 2.54 bsc 0.100 bsc h 0.76 1.27 0.030 0.050 j 0.20 0.30 0.008 0.012 k 2.92 3.43 0.115 0.135 l 7.62 bsc 0.300 bsc m --- 10 --- 10 n 0.76 1.01 0.030 0.040 seating plane 1 4 5 8 a 0.25 m cb ss 0.25 m b m h c x 45 l dim min max millimeters a 1.35 1.75 a1 0.10 0.25 b 0.35 0.49 c 0.18 0.25 d 4.80 5.00 e 1.27 bsc e 3.80 4.00 h 5.80 6.20 h 0 7 l 0.40 1.25 0.25 0.50 notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. dimensions are in millimeters. 3. dimension d and e do not include mold protrusion. 4. maximum mold protrusion 0.15 per side. 5. dimension b does not include mold protrusion. allowable dambar protrusion shall be 0.127 total in excess of the b dimension at maximum material condition. d e h a b e b a1 c a 0.10
tl062 tl064 http://onsemi.com 9 n suffix plastic package case 64606 issue l d suffix plastic package case 751a03 (so14) issue f outline dimensions 17 14 8 b a f hg d k c n l j m seating plane notes: 1. leads within 0.13 (0.005) radius of true position at seating plane at maximum material condition. 2. dimension l to center of leads when formed parallel. 3. dimension b does not include mold flash. 4. rounded corners optional. dim min max min max millimeters inches a 0.715 0.770 18.16 19.56 b 0.240 0.260 6.10 6.60 c 0.145 0.185 3.69 4.69 d 0.015 0.021 0.38 0.53 f 0.040 0.070 1.02 1.78 g 0.100 bsc 2.54 bsc h 0.052 0.095 1.32 2.41 j 0.008 0.015 0.20 0.38 k 0.115 0.135 2.92 3.43 l 0.300 bsc 7.62 bsc m 0 10 0 10 n 0.015 0.039 0.39 1.01 a b g p 7 pl 14 8 7 1 m 0.25 (0.010) b m s b m 0.25 (0.010) a s t t f r x 45 seating plane d 14 pl k c j m notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. dim min max min max inches millimeters a 8.55 8.75 0.337 0.344 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.228 0.244 r 0.25 0.50 0.010 0.019
tl062 tl064 http://onsemi.com 10 notes
tl062 tl064 http://onsemi.com 11 notes
tl062 tl064 http://onsemi.com 12 on semiconductor is a trademark and is a registered trademark of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circui t, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may b e provided in scillc data sheets and/or specifications can and do vary in dif ferent applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its paten t rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indem nify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and re asonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized u se, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employ er. publication ordering information japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402700 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. tl062/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 8002829855 toll free usa/canada

▲Up To Search▲

Price & Availability of TL062-D

	To Download TL062-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .